Bead lampshade DIY + SCHEMES
ABAZHUR FROM BEAD OWN HANDS - MASTER CLASS
EVERY PERSON TRIES TO DECORATE YOUR HOUSING USING MODERN SOLUTIONS FOR DESIGN. I'M NOT AN EXCEPTION. LOCATED ON DECK HOLIDAY, I HAVE DESIGNED THE APARTMENT. FROM PARENTS I HAVE GOT AN OLD DESKTOP LAMP. THE BASIS OF THE DEVICE WAS MORE STRONG AND ON THE ELECTRIC PART ALSO EVERYTHING IN THE ORDER, AND THERE'S A FABRIC LAND LAMP, LEAVE THE WISHING THE BEST. CORRECTED THIS INSUFFICIENCY THROUGH BEADS.
It took: fine copper wire (you can take a fishing line), large decorative beads.
She unplugged the lampshade from the base, removed the fabric inserts from it (photo 1). Fine sandpaper removed from the metal frame remnants of paint and polished all surfaces with felt with GOI paste.
I found a suitable scheme for weaving (see fig. 1 on page 15) I decided to start the work from the bottom. I measured the diameters of the circles - the bottom is equal to 94 cm, the top is 58 cm (fig. 2). I also immediately measured the height of the frame, it is equal to 28, see. Based on these values, I prepared the necessary number of beads.
I put beads on the wire exactly around the circumference and attached a ready-made snake to the bottom ring with a nylon thread. This basis, from it began weaving according to the scheme.
According to the figure you need to dial on 3 beads, but, based on the size of the frame, I had to dial on 9. Each batch was strung on a wire and screwed it to the bottom ring through every 4 beads (photo 2) to form an arc, and so around the entire circumference.
The second and subsequent rows performed similarly, so that the net was turned, the wire was wound into the hole of two or one middle beads of the bottom row (photo 3, 4)
Gradually rising up, evenly diminishing the beads as necessary, so that in the future a new bead fabric tightly fits the frame of the lamp shade. In the place where the grid adjoined to the edge of the frame, it was additionally fixed with wire for reliability (photo 5)
See also: Bouquet from beads with own hands: a master class (+ photo)
IMPORTANT:
Before weaving, it is necessary to immediately determine the pattern of the future lampshade, because the sequence of the set of beads in color depends on it.
Having reached the top, three beads were strung on the wire. The smaller upper ring of the frame is shaped similarly to the lower one. Inside it is covered with a net of beads (photo 6) which she wove in the same way as the sides.
Note
If it is impossible to pass the wire in two layers into the hole of the bead, you can simply wrap it (see photo).
The lampshade is ready. The last final touch remained - the decoration was decorated with a decorative braid, which was decorated with ruffles made of beads and multi-colored large beads and fixed on the lower ring using thin copper wire (photo 7, 8).
The finished lampshade was fastened to the frame, a bulb was screwed into the holder - the night light is ready.
For the bedroom I also made a lamp with elements of bead weaving (photo 9). I needed a piece of drywall, 4 long needles (bought at a hardware store), gypsum, knitting wire and fabric insulating tape.
She put a thickly-spread gypsum on the drywall and quickly inserted the needles into the solution in the form of a square at a distance of about 5-6 cm from each other.
At height 50, see all knitting needles knitted together. Then she twirled the twigs and roots in all directions in different directions with knitting wire.
The husband and son soldered 20 LEDs and connected the circuit to the wire with the power supply.
Ready "garland" distributed on the branches. According to the schemes (Fig. 3, 4). she wove up buds and leaves (photo 10) and fixed everything on the branches next to the light bulbs.
The whole frame of the tree wrapped fabric black tape. The roots and the trunk from the bottom are decorated with plaster, diluted to the consistency of thick cream. The upper part of the stem and twigs left in the tape. Ready night light painted with acrylic paint.
To show the principle of weaving, the author used beads of different colors in the 2-5 photo.
ABAZHUR FROM BEADS - DIAGRAM
See also: Orchid from beads with your own hands - photo and master class
USEFUL VIDEO - BEAD LAMP WITH YOUR OWN HANDS
© Author: Maria Grechiho, Soligorsk. Photo by the author and Irina Savosina
TOOLS FOR MASTERS AND MASTERS, AND HOME GOODS ARE VERY CHEAP. FREE SHIPPING. THERE ARE REVIEWS.
Below other entries on the topic "How to make your own hands - a householder!"
- A bag of old jeans and wool with your own hands - a step-by-step description and photo
- DIY picnic basket from shoe box
- DIY reusable protective face mask + DIAGRAM + video
- Decoupage plates using craquelure technique: a master class
- Do-it-yourself Roman curtain for a bathroom + scheme
- We make a card with a butterfly with rhinestones with our own hands together with the child
- How to make a clutch for a pram - photo and diagram
- Wicker rug on the floor with your own hands + ideas of rugs from readers
- Printing on fabric with acrylic paints and DIY stamps for this
- Do-it-yourself preparation and coloring of straws for applications
Subscribe to updates in our groups and share.
Let's be friends!